Fat Bob's Garage - 2011 / Ford / All Products

Ford F150 Light Racing Adjustable Upper Control Arms (Pair) 2004-2019

Thu, 15 Aug 2019 13:38:13 GMT

Ford F150 Light Racing Adjustable Upper Control Arms (Pair) 2004-2019
Buy Now: $849.96

Ford F150 Light Racing Adjustable Upper Control Arms (Pair) 2004-2019

Improve droop travel, drivability and tire wear as well as adjusting tire position in your wheel well with SPC's adjustable front upper control arms. Featuring an upgraded greaseable ball joint and SpecRide™ bushings, this arm is designed to correct alignment angles while maintaining factory ride quality. SPC's integrated tubular and cast steel designs provide the strength and durability needed for the most demanding environments. These remove and replace arms are sold in pairs.

Get more droop travel: SPC's arm has improved clearance to get around the spring bucket. With 80° of articulation in the upgraded ball joint and free pivoting bushings, SPC's arm gives you maximum droop travel.
Get your drivability and tracking back: When you lift your truck you affect caster and camber. SPC's arms have +1° of caster built into them. Using its patented ball joint design the arm will get you ±2° of caster and ±2° of camber, so you can put your alignment angles back to specification.
Get your tire where you want it in the wheel well: Use adjustment in the control arm and on the OE lower cams to maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming.

Adjustment range: Camber ±2.0°
Caster ±2.0°
Installation time: .8 hr/side

Vehicle Application:
2004 - 2019 Ford F150*

2006 - 2008 Lincoln Mark LT

2007 - 2017 Ford Expedition

*Does NOT fit Raptor models

***This product is not discountable***

Visit Ford to see additional products in this category.

Ford F250/F350 Super Duty 2" Cree LED Fog Light Kit Black Series 2011-2016

Wed, 20 Feb 2019 14:35:00 GMT

Ford F250/F350 Super Duty 2" Cree LED Fog Light Kit Black Series 2011-2016
Buy Now: $109.95

Ford F250/F350 Super Duty 2" Cree LED Fog Light Kit Black Series 2011-2016

Bring the state-of-the-art power and efficiency of LED lighting to your Ford Super Duty's factory fog lights with Rough Country's new Black-Series 2-inch Fog Light LED Kit. This clever LED & mount combo allows you to swap out the factory fog lights with Rough Country's 2-inch LED Cubes, offering increased illumination and killer, good looks that blend right in with the 2011-2016 design.The black panel design offers jaw-dropping good looks that blend perfectly with any vehicle using black accents like grilles, wheels, bull bars or steps! The easy-to-install mounts feature a 100% bolt-on install process and can be performed with common tools in no time flat.

Light up the road with 36 watts and 2880 Lumens of output power. Each kit includes a set of wiring adapters that quickly connect to your existing fog light wiring harness for instant installation, and also includes an optional, premium flat-wound wiring harness with in-line fuse and on/off switch. For peace of mind, each LED also includes Rough Country's 3-year Warranty.

Features:

Installs in factory fog light location
1440 lumens each
18 watts each
30 degree spot beam
Each light contains (6) 3 watt high intensity Cree LEDs
IP67 waterproof rating
Durable die cast aluminum housing
Includes wiring harness
3 year warranty

Notes:
Mounts to standard factory bumper ONLY

For off road use ONLY

Kit includes:

(2) 2" LED square lights, (2) fog light mounting brackets and hardware

Vehicle Application:
2011-2016 Ford F250 Super Duty 2WD/4WD
2011-2016 Ford F350 Super Duty 2WD/4WD

***This product is not discountable***

Installation Instructions - PDF Download

Visit Ford to see additional products in this category.

Ford Ranger Light Racing Adjustable Upper Control Arms (pair) 2011-2014

Thu, 23 Aug 2018 10:10:00 GMT

Ford Ranger Light Racing Adjustable Upper Control Arms (pair) 2011-2014
Buy Now: $1,024.95

Ford Ranger Light Racing Adjustable Upper Control Arms (pair) 2011-2014

Get more droop travel: SPC's arm has improved clearance to get around the spring bucket. With 80° of articulation in the upgraded ball joint and free pivoting bushings, SPC's arm gives you maximum droop travel.
Get your drivability and tracking back: When you lift your truck you affect caster and camber. SPC's arms have +1° of caster built into them. Using its patented ball joint design the arm will get you 0° to +4° of caster and ±3° of camber, so you can put your alignmnet angles back to specification.
Get your tire where you want it in the wheel well: Use adjustment in the control arm and on the OE lower cams to maximize alignment angles and move oversized tires forward in the wheel well to minimize or avoid fender trimming.

Front Adjustment range:
Camber +/-3.00 degrees

Caster 0 to +4.00 degrees
Installation time: .8 hr/side
Required: 1 per axle

Vehicle Application:
2011 - 2014 Ford Ranger

***This product is not discountable***

Visit Ford to see additional products in this category.

Ford F250 SuperDuty 3" Suspension Lift 4WD 2011-2016

Mon, 19 Mar 2018 10:14:00 GMT

Ford F250 SuperDuty 3" Suspension Lift 4WD 2011-2016
Buy Now: $769.95

Ford F250 SuperDuty 3" Suspension Lift 4WD 2011-2016

Kit Contents:

Front: Lifted coil springs, trac bar drop bracket, radius arm drop brackets, hardware.
Rear: 2" lift blocks, u-bolts, hardware.
Shocks: (4) Premium N3 series.

Notes:
Does NOT fit Dually models.
Does NOT fit F350 models.

Benefits:

Easy bolt-on installation
Increased ground clearance
Levels the front with the rear of the truck
Radius arm drop brackets allow for properly set caster.
Proper caster is crucial to maintaining factory handling and driveability.

Estimated Install Time: 3 - 4 hours
Wheel Backspacing: Factory
Recommended Tire Size: 35x12.50

Vehicle Application:
2011-2016 Ford F250 4WD

Installation Instructions - PDF Download

***This product is not discountable***

Visit Ford to see additional products in this category.

Ford F250/F350 8" Coilover 4-Link Suspension Lift Kit 4WD 2011-2016

Tue, 27 Feb 2018 12:44:00 GMT

Ford F250/F350 8" Coilover 4-Link Suspension Lift Kit 4WD 2011-2016
Buy Now: $6,464.56

Ford F250/F350 8" Coilover 4-Link Suspension Lift Kit 4WD 2011-2016

Designed to allow the installation of Fox 2.5 factory series remote reservoir coilovers, this new system far surpasses the performance and capability of your Super Duty's stock suspension with more stability, improved handling, and better dampening in any terrain. Michigan built and Moab tested, these new coilover conversion 4-link systems are built to perform.

The system utilizes a pair of Fox 2.5 factory series remote coilovers tuned specifically to optimize suspension performance on the diesel equipped Ford Super Duty. The 8" travel coilovers feature a smooth bore and honed seamless alloy body, 7/8" hardened steel carbon shaft, Eibach coil springs, black anodized machined 6061-T6 billet aluminum mounts, and FOX's DSC (dual speed compression) adjustment technology on DSC equipped coil-overs. DSC is the next big thing in suspension performance allowing for easy adjustment of the your truck's suspension compression dampening so you can dial in the ideal ride performance to soak up the bumps, both large and small. The DSC has 12 adjustment points for the high speed compression as well as 10 adjustment points for the low speed compression allowing you to make large or small changes to further improve your performance. Adjustments can be made by simply twisting the "blue" high speed and "gold" low speed compression knobs located on the end of the remote reservoir of the FOX 2.5 coilovers. No tools or shop adjustments needed, allowing you to tune the suspension out on the trail.

The key to mounting these new DSC coilovers are the new brackets supplied by BDS. In place of the factory stamped steel coil buckets BDS includes a pair of the massive 1/4" thick steel, gusseted construction coilover mounting brackets designed to bolt in place using the factory frame holes. This provides a stout mounting point for the new Fox 2.5 coilovers with provisions for the remote reservoirs as well as an auxiliary shock. The auxiliary shock mount will accept anything from the supplied Fox 2.0 Performance series shocks up to the massive 3.0 Fox Factory series cylinders. At the axle, new double-shear C/O mounting brackets bolt in for a direct replacement to the factory coil seats. All brackets are finished in a durable textured black powder coat finish with integrated mounting tabs to retain the factory brake and ABS lines.

To complement the increased performance of the new coilovers, BDS designed the kit around the popular BDS 4-link conversion to upgrade the stock stamped steel factory radius arms. The BDS Super Duty 4-Link conversion has long been a popular solution for 2005-2016 Super Duty owners looking to improve their trucks drivability and performance. The full replacement 4-link frame brackets bolt into factory holes and create a solid mounting location for the massive tubular 4-link arms. These arms allow the front suspension geometry to be optimized for control and handling through all types of terrain. The front portion of the lift system also includes a forged drop pitman arm and front track bar relocation bracket to correct steering and track bar angles as well as to center the axle under the vehicle. Front bump stop extensions, sway bar drops, and brake line relocation brackets round out the front of this system. In the rear, full replacement BDS Glideride leaf springs provide the lift needed to level and level the stance. The springs are a 5-leaf design with built in overload leaf to assist when carrying heavy loads. New black e-coated u-bolts, brake line brackets and Fox 2.0 performance gas shocks are supplied to round out the 8" coilover conversion 4-link system.

Notes:

Exhaust modification may be required to clear front driveshaft (gas only)
Front bumper spacer kit may be required to run 38"x15.50" tires
Although extremely rare, front driveline vibration may occur
If equipped with 2-piece rear driveshaft, driveshaft alignment kit (#123406) will be required
Front driveshaft u-joints may max out at full droop. If so, a new front shaft will be required.
If equipped with rear sway bar, #123009 is required.
U-bolts will not work on dually.
Front auxiliary shocks can be omitted from kit - system can be used with C/O installed alone
BDS leaf springs are not intended for use beyond the truck's maximum payload capacity. Trucks equipped with overload springs will only have the capacity of a non-overload equipped truck. If heavy payload use is desired, supplemental rear air bags are recommended.

Tire & Wheel Combinations:

38" x 15.50" w/17 x 9 and 4.5" back spacing
38" x 15.50" w/18 x 9 and 4.5" back spacing
38" x 15.50" w/20 x 9 / 20 x 10 and 4.5" back spacing

Estimated Install Time: 8-10 hours

Vehicle Applications:
2011-2016 Ford F250 Super Duty 4WD
2011-2016 Ford F350 Super Duty 4WD

Installation Instructions - PDF Download

Visit Ford to see additional products in this category.

Ford F150 2" Leveling Strut Extension Kit 2009-2018

Tue, 6 Feb 2018 15:08:00 GMT

Ford F150 2" Leveling Strut Extension Kit 2009-2018
Buy Now: $54.95

Ford F150 2" Leveling Strut Extension Kit 4WD 2009-2018

Features:

Easy bolt-on installation
Maintains factory ride quality
Increased ground clearance
Levels the front with the rear of the vehicle
No need to disassemble your struts to install
Built from heavy-duty proprietary composite material that will never rust or succumb to the elements

Kit Includes:

Front: Strut extensions & hardware

Max Tire Size: 33x12.50

Wheel Offset: Factory

Estimated Install Time: 2-3 hours

Vehicle Application:

2009 - 2018 Ford F150 2WD/4WD

2017 - 2018 Ford F150 Raptor 4wd

Notes:

Does NOT fit 2009-2016 Raptor models

Installation Instructions - PDF Download

***This product is not discountable***

Visit Ford to see additional products in this category.

BDS Ford F250/F350 Recoil Traction Bars 99-16 4wd

Tue, 13 Sep 2016 14:59:00 GMT

BDS Ford F250/F350 Recoil Traction Bars 99-16 4wd
Buy Now: $1,129.99

BDS Ford F250/F350 Recoil Traction Bars 99-16 4wd

BDS Suspension introduces a revolutionary spring loaded traction bar system engineered to improve traction and limit axle wrap without negatively affecting suspension travel or ride quality. These next generation RECOIL traction bars offer you the freedom to tune the spring tension for optimal performance on-road, off-road, towing, or competition pulling. These traction bars can be used on stock height or lifted trucks and work with both lift blocks and replacement leaf spring kits. They use a full floating design that won't bind up allowing the full range of wheel travel without limiting articulation.

The RECOIL traction bars mount to the vehicle using fabricated 1/4" steel brackets. Bracket kits are vehicle specific. The frame brackets install by drilling mounting holes for the brackets while the axle brackets install using a set of u-bolts. The traction bars and mounting brackets use a durable gloss black powdercoat finish.

These new RECOIL traction bars are built to the highest standards featuring quick and easy adjustment while installed on the vehicle. To adjust spring tension, use the supplied spanner wrenches at the axle to loosen the jam nut. From there the main bar can be rotated to load or unload the springs at the frame side of the bar. Using the concave end of the wrench handle against the frame end check the location of the end of the main bar in relation to the notches on the wrench to verify the load on the springs, the shorter the distance the more loaded the springs are. Repeat this process on the other traction bar and use the wrenches to tighten down the jam nuts and you are ready to go!

Vehicle Application:
1999 - 2016 Ford F250/F350 4wd

Notes:

Specific kits for long box and short box models
Fits 0-6" of rear lift
Fits single rear wheel models only
Will work with vehicles equipped with factory rear sway bar

Visit Ford to see additional products in this category.

Ford Expedition Econ Economy Power Programmer 2011

Wed, 28 Oct 2015 12:19:00 GMT

Ford Expedition Econ Economy Power Programmer 2011
Buy Now: $329.99

Hypertech Econ Economy Power Programmer 2011

The Max Energy E-CON™ Economy Power Programmer is designed for the driver who needs better fuel mileage and more power, but doesn’t want to pay for other high-performance features they may not need. Every E-CON is programmed with Hypertech’s Max Energy™ Tuning, the best optimized fuel tuning programs possible that increase horsepower and torque. Max Energy Tuning extracts every bit of energy possible out of every molecule of fuel giving you more miles at part-throttle and and more power at wide-open throttle. In order to increase engine efficiency, horsepower and torque, our engineers optimize the spark and fuel curves point by point over the entire rpm band. With the additional power and optimized transmission functions, drivers use less fuel to accelerate and maintain cruising speeds without the torque converter un-locking and transmission down-shifting to a lower gear. The results are improved power and maximum fuel mileage. Hypertech's customers are claiming 2 to 6 mpg gains and a substantial increase in horsepower and torque.

Regular octane tuning
DTCs Read and Clear
Return Back to Stock
Internet Updateable

Vehicle Application:
2011 Ford Expedition 5.4

Product Manual - PDF Download

Visit Ford to see additional products in this category.

Ford Expedition Max Energy Power Programmer 2011

Wed, 28 Oct 2015 12:19:00 GMT

Ford Expedition Max Energy Power Programmer 2011
Buy Now: $379.99

Hypertech Max Energy Power Programmer 2011

Max Energy Tuning extracts every bit of energy possible out of every molecule of fuel giving you more miles at part-throttle and more power at wide-open throttle. In order to increase engine efficiency, horsepower and torque, our engineers first optimize the spark and fuel curves point by point over the entire rpm band. With the additional power and optimized transmission functions, drivers use less fuel to accelerate and maintain cruising speeds without the torque converter un-locking and transmission down-shifting to a lower gear. The results are maximum power and fuel mileage.

Optimized engine tuning for regular and premium octane
Speedometer/odometer correction for non-stock tire sizes from 24"-54" & rear gear ratios from 2.73:1-4.56:1
Adjust automatic transmission shift points & firmness
Raise top speed limiter to match the speed rating of factory approved high performance tires
Adjust RPM rev limiter
Adjust cooling fan "on/off" temps
Read, display, & clear DTCs

Vehicle Application:
2011 Ford Expedition 5.4

Product Manual - PDF Download

Visit Ford to see additional products in this category.

Ford Expedition Speedometer Calibrator 2011

Wed, 28 Oct 2015 12:19:00 GMT

Ford Expedition Speedometer Calibrator 2011
Buy Now: $229.99

Hypertech Speedometer Calibrator 2011

Hypertech’s Speedometer Calibrator can correct the speedometer and odometer for tires up to 54 inches (depending on the application), and/or non-stock rear gear ratios. This new device is engineered for consumers that want the speedometer recalibration functions of the Max Energy Programmer without the additional expense of the other tuning features. The Speedometer Calibrator comes with a USB cable and a CD containing software to enable quick updates and upgrades over the internet. For an additional charge, the Speedometer Calibrator can be upgraded to a Max Energy Power Programmer via the internet to include all the Max Energy features available for that vehicle.

Simply plug Hypertech's Speedometer Calibrator into the vehicles under-dash connector, select the new tire height and/or new rear gear ratio, and in a matter of minutes, the vehicle's computer is reprogrammed for accurate readings (as required by law).

Vehicle Application:
2011 Ford Expedition 5.4

Product Manual - PDF Download

Visit Ford to see additional products in this category.